• 01-26-2006
    GreenGnu
    Burton X Base Binding 4x4 mounting discs
    Hey guys, wondering if anyone out there has a set of these badboys, I have the 3D discs, but i now have a 4 hole board, little did i know they were so proprietary. No regular burton discs i have found will work.
    I have the Burton X bindings found here:
    http://www.outdoorreview.com/cat/sno...3_3147crx.aspx
    and am looking for the 4x4 mounting plates for them, The dimensions of the discs are as follows:
    Thickness: 7mm or 1/4 inch
    Top diameter: 10cm or 3 15/16 inches
    Bottom diameter: 8cm or 3 5/32 inches

    If anyone has a set of discs that will fit please let me know!

    Thanks for the help

    GreenGnu
  • 01-27-2006
    GreenGnu
    Unfortuneately, i talked to 3 different people at Burton customer service, and to no avail. Thank you for the advice in how to drill the discs, i was planning on drilling them if i couldnt find replacements, but you gave some good advice on how to do it most effectively. Hopefully someone with a set will read this!

    Tyler
  • 01-27-2006
    NoKnees
    Amazingly you can sometimes get lucky working directly with Burton's customer service directly for old parts.

    If that doesn't work, time to bust out the old power drill and create a couple new holes in your Burton 3x disks... Not prefered, but if it means getting another season or two out of some older bindings, go for it. Been there done that myself with some old plastic burton discs without an issue... Use a counter-sink drill bit, washers, and the flat head screws you can find to spread out the stress that the new holes and screws may put in the baseplate without creating uncomfortable bumps under your arches...
  • 01-27-2006
    MARK
    That's a 98/99 season X binding. The disc teeth size, etc. was slightly changed a year later which is why you can't find any that mesh right now. Never fear though, I have 98/99 black Burton 4x4 discs for you. Send me an email at marktoms@mindspring.com. Also include the resorts that you mostly ride in the email.
  • 01-27-2006
    MARK
    You asked the wrong 3 people :D
  • 01-27-2006
    GreenGnu
    Mark is my hero! so as of now this is hopefully a very solved problem, thanks to noknees for his advice, and Mark for hooking me up with the parts, you guys pulled through quickly! ill definitely stick around these forums as im sure i will have many more questions in the future!

    Thanks again!

    Tyler
  • 01-27-2006
    MARK
    As an added incentive to stick around, NoKnees on occassion shows off his legs in posted beach pics as well :o
  • 01-27-2006
    NoKnees
    You trying to get him to run and hide or stick around? Either way, you're all in luck as my legs won't be spending much time at the beach for a few months yet...

    Anyway, glad Mark can hook you up Tyler. Not many folks hang around the forums here, but the few that due are usually good for something...
  • 12-25-2009
    FLiPSyDe71
    XBase use with "The Channel"
    Mark... any chance you have any modified discs for the X Base bindings that will work with Burton boards that have the new single Channel mounting system?
  • 12-26-2009
    MARK
    Sorry I don't. You could probably modify some, but keep in mind that Burton changed the disc tooth pattern in like 2001, so you would need to use the apropriate discs that match your current model year of binding.
  • 12-26-2009
    FLiPSyDe71
    Hmm... do you have any spare aluminum discs laying around that I can buy off you? I want to experiment but don't want to start drilling my only pair. Mine are older models from around '98.
  • 12-26-2009
    MARK
    Yours discs should be composite, not aluminum. You have the dark ones right?
  • 12-26-2009
    FLiPSyDe71
    No, they're not dark, I'm sure its aluminum... definitely a light metal. Here's a pic:
    http://i126.photobucket.com/albums/p...1/IMG_5205.jpg
  • 12-28-2009
    MARK
    Yeah, I don't have any that will work .
  • 01-30-2010
    blakebobit
    If any of you would be willing to part with your X-Base bindings I would love to get some again. Please let me know. I've been looking for another pair for the last 4 years.

    I still have the plates and replacement heel cup straps, but need the bindings. I'm also willing to buy any more replacement parts or broken bindings that can be salvaged.

    Blake
    blake (at) blake bobit (dot) com
  • 09-16-2010
    blakebobit
    Quick update. Just got a new pair of X2 Base bindings from a nice guy who found my post on this forum. Thank you!!!!!!!

    Was wondering if any of you had tried doing CNC machining to produce more base plates to work with 4x4 or the new channel system?
  • 09-17-2010
    MARK
    Sweet! Glad you got a set.